The new Waze Wiki, aka Wazeopedia, is now live at Wazeopedia.waze.com! While this legacy wiki will remain accessible for the time being, it is no longer updated by the community. For the most up-to-date guidance, please visit your local Wazeopedia.

Please do not make any more updates to these legacy wiki pages, all future updates should be made in your country's local Wazeopedia.

Clock over a larger globe

Difference between revisions of "Limited Access Interchange Style Guide"

From waze
Jump to: navigation, search
(Complex Collector/Distributor: real complex case added)
(Complex Collector/Distributor: Added paragraph to start simple. Remove "more to come")
Line 123: Line 123:
  
 
A Collector/Distributor is considered complex if there are multiple exits and entrances connected to the Collector/Distributor.
 
A Collector/Distributor is considered complex if there are multiple exits and entrances connected to the Collector/Distributor.
 +
 +
Ideally you will '''not''' have to implement any of the complex layouts described in this section.  Start by representing the ramps in the simplest manner possible and see how they perform for a while.  If everything is mapped correctly and navigation still tries to have drivers bypass the mainline Freeway, then and only then modify the layout with the following suggestions.
  
 
If we are lucky, we can still restrict the bypass movement with the single central node like we did for the [[#Collector.2FDistributor_Cloverleaf|Collector/Distributor Cloverleaf]] example.  Notice how all the exits are either before or at the central node (highlighted in the next image) and all the entrances are at or after the central node.
 
If we are lucky, we can still restrict the bypass movement with the single central node like we did for the [[#Collector.2FDistributor_Cloverleaf|Collector/Distributor Cloverleaf]] example.  Notice how all the exits are either before or at the central node (highlighted in the next image) and all the entrances are at or after the central node.
Line 143: Line 145:
  
 
As a worse case scenario, you may have a situation where traffic can enter early in the Collector/Distributor and can legally exit at any of the exits along the Collector/Distributor.  In this case you will need to carefully create junctions with restricted turns or even additional ramps to enable the legal movements.
 
As a worse case scenario, you may have a situation where traffic can enter early in the Collector/Distributor and can legally exit at any of the exits along the Collector/Distributor.  In this case you will need to carefully create junctions with restricted turns or even additional ramps to enable the legal movements.
 
''(more to come)''
 

Revision as of 02:26, 24 August 2012

Limited Access Interchanges

See also: Wikipedia article on Road Interchanges

When two roads meet in a limited access interchange (any situation where travel between grade separated roads is facilitated by ramps or slip roads alone), extra care must be taken.

If an exit ramp lines up with an entrance ramp, care must be taken to restrict the straight through direction to prevent "ramp-to-ramp routing" where the routing engine may try to take a shortcut from the Freeway, to the exit ramp, to the entrance ramp, and back to the Freeway instead of staying on the Freeway. That motion is inefficient and may be illegal in certain jurisdictions.

Care must be taken to not enable all turns in any situation where ramps meet unless all possible flows of traffic have been considered!

We also have to pay attention to the Level of the road segments since there will typically be many bridges and overpasses for any limited access interchange. If two roads cross without connecting, their levels must be different.

The following sections discuss some of the common Interchange designs. Note that some Interchanges may be a hybrid of these basic designs where one side or quadrant of the interchange may differ from the others.

Diamond Interchange

Jct diamond.png

See also: Diamond Interchange article on Wikipedia

Common in wide open spaces where land acquisition and geography are not concerns, this Interchange design has ramps equally distributed across all 4 quadrants.

In the simplest form, this can be represented as single connections from the ramps to the surface street.

Note: Be sure to restrict the straight through motion from the exit ramp onto the entrance ramp on the other side of the road. This will prevent the routing server from trying to route someone off the freeway just to get back on it. Even though it may be a legal direction for a vehicle, turn restrictions are only for controlling routing directions.

Jct diamond simple turns.png

If the ramps connect to the surface street at multiple points (be sure to read How complex should ramps be?, we have to avoid ramp-to-ramp routing as well as illegal turns which should use another ramp. First we see the turns that must be restricted for the exit ramps:

Jct diamond cplx turns off L.png Jct diamond cplx turns off R.png

Then we see what must be restricted for the entrance ramps:

Jct diamond cplx turns on.png

Note on Levels: The single surface street segment between the inner most ramps should be either raised or lowered in relation to the freeway segments depending on the actual geography at the interchange.

Cloverleaf Interchange

Jct cloverleaf.png

See also: Cloverleaf Interchange article on Wikipedia

In a Cloverleaf Interchange, left turns are eliminated from all movements between the Freeway and the surface street. First check the exit ramps.

Jct cloverleaf off outer turns.png Jct cloverleaf off inner turns.png

Then check the entrance ramps for illegal turns.

Jct cloverleaf on turns.png

The connections to the Freeway segments may be treated in two ways:

Jct cloverleaf options.png
  1. (top) we can have the inner entrance and exit ramps have their own junction nodes with the Freeway. Do NOT use this approach if there are Collector/Distributor Lanes (or a similar situation) involved.
  2. (bottom) we can have the entrance and exit ramps share a single junction node with the Freeway. This allows us to eliminate the very short Freeway segment that may exist between the inner entrance and exit ramps.
    It is best to offset this shared junction onto the Entrance ramp side of the surface street. This prevents the junction from accidentally being connected to the surface street or looking like it does. We favor the Entrance ramp side, because this would result in a slightly earlier exit instruction which is of course preferred over a late exit instruction.

The determining factor of which design to use will partly depend on the actual size and scale of the specific interchange and if there is a Collector/Distributor involved.

Note on Levels: The single surface street segment between the inner most ramps should be either raised or lowered in relation to the freeway segments depending on the actual geography at the interchange.

Folded Diamond

Jct folded diamond.png

See also: Discussion of Folded Diamonds and A2/B2 Partial Cloverleafs on the Partial Cloverleaf Interchange article on Wikipedia

Geography or property ownership may prevent the ability for an interchange to be constructed with all ramps evenly distributed across the 4 quadrants of the interchange. When only two quadrants are used, it is typically called a Folded Diamond (basically a sub-type of a Partial Cloverleaf Interchange). The ramps may be all on one side (as in the examples in this section) or they may be located in diagonally opposed quadrants.

The unique situation presented by the Folded Diamond arrangement is having both Entrance and Exit ramps terminating on the same side of the surface street. Ideally both ramps should terminate on the same junction node to permit us to easily restrict the illegal and usually impossible ramp-to-ramp movement.

Jct folded diamond u-turn.png'

Like with a basic Diamond Interchange, often it will be necessary to represent the ramps making multiple connections to the surface street (Be sure to read How complex should ramps be?. Restrict all non-permitted turns.

Jct folded diamond off turns L.png Jct folded diamond off turns R.png Jct folded diamond on turns.png

Note on Levels: Similar to a basic Diamond interchange, in most cases only the segment of the surface street that crosses the Freeway segments will need to be adjusted up or down.

Single Point Urban Interchange (SPUI)

Jct SPUI.png

See also: Single Point Urban Interchange article on Wikipedia

A SPUI is a very space and flow efficient design, but it takes extra attention to ensure the turns are correct. And as the name indicates, ideally there should be a single junction in the center. You may need to tweak the geometry of segments a bit off of alignment from the real physical world, but it should be minor if the interchange is a true SPUI.

The outer branches of the exit ramps are very much like in the case of a diamond interchange:

Jct SPUI off outer turn.png

Where things get complicated is the inner branches leading to the Single Point. You need to avoid ramp-to-ramp in two directions and a reverse flow turn. Note: The ramp-to-ramp motion to facilitate a U-Turn (the top left arrow in the image below) may or may not be allowed depending on the specific interchange. Please validate this turn.

Jct SPUI off inner turn.png

Luckily the entrance ramp restrictions are similar to the diamond interchange:

Jct SPUI on turn.png

If you were to look at all the restricted turns at once, you may get the false impression that something is very wrong. But as you now know, a SPUI has almost as many restricted turns as allowed ones.

Jct SPUI all turns.png

Note on Levels: The two surface street segments (between the outer ramps and connected to the Single Point) and the 4 ramp segments connected to the single point should all be the same level, either one higher or one lower than the level of the freeway segments above/below the single point.

Collector/Distributor Lanes

These are lanes parallel to but physically separated from the lanes of a Limited Access Road that serve to keep merging traffic out of the flow of through traffic on the mainline Freeway.

Collector/Distributor Cloverleaf

This is a Cloverleaf interchange that is connected to a Collector/Distributor instead of directly to the main roadway. Here is an example which matches the physical world but has a major deficiency.

Jct fc cloverleaf bad.png

At first it appears that this layout allows everyone to get where they are going. The problem is that it allows MORE than it should. It is possible to exit the mainline Freeway and stay on the Collector/Distributor, bypassing the Cloverleaf, and merge back onto the mainline Freeway.

Although this may be a way to avoid traffic on the mainline Freeway, doing so is inefficient, may be unsafe, and is outright illegal in some areas. Therefore we need to tweak our design a little...

Jct fc cloverleaf good.png

In this example, we have eliminated the ramp segment joining the two loops of the cloverleaf and the Collector/Distributor ramps. Now they all connect at a single point and we are therefore able to restrict the turn that allowed drivers to use the Collector/Distributor as a bypass.

Complex Collector/Distributor

A Collector/Distributor is considered complex if there are multiple exits and entrances connected to the Collector/Distributor.

Ideally you will not have to implement any of the complex layouts described in this section. Start by representing the ramps in the simplest manner possible and see how they perform for a while. If everything is mapped correctly and navigation still tries to have drivers bypass the mainline Freeway, then and only then modify the layout with the following suggestions.

If we are lucky, we can still restrict the bypass movement with the single central node like we did for the Collector/Distributor Cloverleaf example. Notice how all the exits are either before or at the central node (highlighted in the next image) and all the entrances are at or after the central node.

Jct cmplx collector 1.png

It becomes more complicated if entrances and exits are more mixed. In the following example, there is an entrance before an exit and the highlighted path shows this entering traffic crossing the exiting traffic we dealt with in previous examples. If we use the same restricted turn on the same node as in previous examples, we block traffic entering from the right-most entrance from being able to get to the mainline Freeway. If we enable that turn, now we are no longer blocking the bypass movement.

Jct cmplx collector 2a.png

To get the control we require, we need to run the entrance ramp up to the node of the last exit. This allows the exiting traffic to be kept separate from the entering traffic. In the next example, we have modified the right-most entrance so it connects further down the Collector/Distributor. Even if the Collector/Distributor itself is only one lane, we want to have these parallel road segments through the area. They can be close together, but do not overlap them. You will have segments overlapping, but be sure not to junction them together.

Jct cmplx collector 2b.png

Now we can restrict the exiting traffic from using the Collector/Distributor as a bypass of the mainline Freeway as we have previously without impacting the entering traffic.

In a more complicated case, you will need to create parallel paths for exiting and entering traffic for a majority of the Collector/Distributor's length. In the following example, the path for exiting traffic is highlighted and the ramps available for entering traffic appear normally. There is no mixing of entering and exiting traffic in this logical view of the Collector/Distributor even if traffic is mixing in reality.

Jct cmplx collector 3.png

As a worse case scenario, you may have a situation where traffic can enter early in the Collector/Distributor and can legally exit at any of the exits along the Collector/Distributor. In this case you will need to carefully create junctions with restricted turns or even additional ramps to enable the legal movements.